Access Point cisco مدل WAP200

Cisco WAP200 Wireless-G Access Point: PoE/RangeBooster Cisco Small Business Access Points Wireless Access Point That Extends Network Connectivity for Small Businesses Highlights ● Increases wireless throughput and range and reduces dead spots in the wireless coverage area with RangeBooster technology ● Connects to Power over Ethernet devices, simplifying installation and eliminating the need for and cost of installing external power supplies ● Protects network traffic to safeguard business information with enhanced security, including advanced encryption and security monitoring for additional visibility ● Provides consistent network performance with integrated quality of service to support voice and video applications ● Simplifies installation and configuration with easy-to-use web interface Product Overview RangeBooster technology is a compatible add-on to standard Wireless-G that can nearly double your wireless networks range and increase its throughput by up to 35 percent. Unlike ordinary wireless technologies that are confused by signal reflections, RangeBooster uses two smart receivers at each end to detect and decode reflected signals at distances where standard technologies give up. Youll find that dead spots in the wireless coverage area are reduced, too. The advanced security features make this solution ideal for your business. Advanced wireless security using Wi-Fi Protected Access (WPA2) with up to 256-bit encryption, and Wireless Security Monitoring give your business the visibility and protection it needs. Used when Cisco(r) WUSB 200, WMP200 or WPC200 Wireless adapters are present, Wireless Security Monitoring alerts you of possible wireless intruders and vulnerabilities in the wireless deployment and gives you visibility into denial-of-service attacks. The Cisco WAP200 Wireless-G Access Point (Figure 1) lets you connect Wireless-G (802.11g) or Wireless-B (802.11b) devices to your wired network so you can add PCs to the network with no cabling hassle. Power over Ethernet (PoE) support makes it easy to install - you can mount the access point anywhere, even without ready access to a power plug. With appropriate PoE support at the other end, you need to run only one cable to the access point to deliver both data and power. Of course, you can also use the included AC adapter if power is available nearby. The integrated quality of service (QoS) features provide consistent voice and video quality on both the wired and wireless networks, enabling the deployment of business-quality voice over IP (VoIP) and video applications. Additional features like multiple basic service set identifiers (BSSIDs), wireless roaming, and auto-channel selection, make this solution ideal for your business. Features ● 10BASE-T/100BASE-TX Ethernet port, autosensing half/full duplex and medium dependent interface (MDI) and MDI crossover (MDI-X) ● Full backward compatibility with 802.11b ● Easy installation and configuration ● Supports Wired Equivalent Privacy (WEP), WPA Pre-Shared Key (WPA-PSK), WPA2-PSK, WPA-ENT, and WPA2-ENT authentication (802.11i ready) ● SMA detachable dipole antennae with 1x2 multiple-input, multiple-output (MIMO) to increase coverage ● Supports PoE or external DC power ● Supports 4 BSSID and 802.1Q VLAN to service set identifier (SSID) mapping ● Supports Simple Network Management Protocol (SNMP) and features an intuitive web-based interface ● Wi-Fi Multimedia (WMM) wireless QoS support, upgradable to 802.11e ● Supports wireless roaming based on 802.11F (Inter-Access Point Protocol [IAPP]) ● Supports access point, bridge mode, and repeater mode ● Supports wireless security monitoring (working together with Cisco WUSB 200, WMP200 or WPC200 client cards) ● Supports wireless client isolation ● Limited lifetime warranty Specifications Table 1 gives specifications, package contents, and minimum requirements for the Cisco WAP200 Wireless-G Access Point. Table 1. Specifications for the Cisco WAP200 Wireless-G Access Point: PoE/RangeBooster Specifications Standards IEEE 802.11g, IEEE 802.11b, IEEE 802.3, IEEE 802.3u, IEEE 802.3af (PoE), 802.1p (QoS priority), 802.1q (VLAN), 802.1X (security authentication), 802.11i ready (security WPA2), 802.11e ready (wireless QoS), 802.11F (wireless roaming) Ports 10BASE-T/100BASE-TX Ethernet, 12V DC power Buttons Reset Cabling type Unshielded twisted pair (UTP) Category 5 LEDs Power, PoE, Wireless, Ethernet Operating system Linux Setup/Configuration Web user interface Built-in web user interface for easy browser-based configuration (HTTP/HTTPS) Management SNMP version SNMP version 1, 2c, 3 Event logging ● Email notification ● Remote syslog Web firmware upgrade Firmware upgradable through web browser Diagnostics Flash, RAM, LAN, WLAN Dynamic Host Configuration Protocol (DHCP) DHCP client Operating Modes Access point Access point mode, point-to-point bridge mode, point-to-multipoint bridge mode, repeater mode Wireless Spec/modulation Radio and modulation type: 802.11b/DSSS, 802.11g/OFDM Channels Operating channels: 11 North America, 13 most of Europe (ETSI and Japan) External antennas 2 (omnidirectional) SMA detachable Transmit power Transmit power (adjustable) at normal temperature range: ● 802.11b: 18~19 dBm ● 802.11g: 14~15 dBm Antenna gain in dBi 2 Receiver sensitivity 802.11.g: 54 Mbps at -72 dBm, 802.11.b: 11 Mbps at -85 dBm Security WEP/WPA/WPA2 WEP 64-bit/128-bit, WPA-PSK, WPA2-PSK, WPA-ENT, WPA2-ENT Access control Wireless connection control: MAC-based SSID broadcast SSID broadcast enable/disable 802.1X IEEE 802.1X support Wireless client isolation Wireless client devices can be isolated from each other either within an SSID or between 2 SSIDs Wireless Security Monitor Scan and classify wireless devices in the network Report new client and access point joining network and suspicious network events (works together with Cisco WUSB 200, WMP200 or WPC200 business client adapters): ● Intrusion alarms (e.g., rogue client detected, spoofed MAC address) ● Denial-of-service alarms (e.g., duration attack, association table full) ● Vulnerability alarms (e.g., access point is not using encryption, access point is broadcasting SSID) ● Other alarms (e.g., low speed connection) Quality of Service QoS ● 4 queues ● Wi-Fi Multimedia (WMM) wireless priority General ● Wireless roaming based on IAPP ● Auto-channel selection Environmental Dimensions W x H x D 6.69 x 8.07 x 7.68 in. (170 x 205 x 195 mm) Unit weight 0.88 lb (0.4 kg) Power 12V 1A DC Input, and IEEE 802.3af compliant PoE Maximum power draw: 3.36W Certification FCC, ICES-003, CE Operating temperature 32 to 104F (0 to 40C) Storage temperature -4 to 158F (20 to 70C) Operating humidity 10% to 85% noncondensing Storage humidity 5% to 90% noncondensing Package Contents ● Cisco WAP200 Wireless-G Access Point ● 2 SMA detachable dipole antennas ● User guide on CD-ROM ● Ethernet network cable ● Power adapter ● Product stands ● Registration card Minimum Requirements ● 802.11b, 802.11g wireless adapter with TCP/IP installed per PC ● Switch/router with PoE support or PoE injector when used with PoE ● Web-based configuration: Java-enabled web browser Product Warranty Limited lifetime hardware warranty with return to factory replacement.