5-Port 10/100M Switch with 4 PoE,total 65 watts,IEEE802,3af,Pre-802,3at,Per-port PoE On/Off,High power delivery 48/30/20/15,4W for 1/2/3/4 PDs.
Introduction
The SP6005P4 supports IEEE 802.3af and pre-802.3at standards
for Power over Ethernet (PoE) with the maximum power delivery
up to 48 Watts. That makes it suitable to various applications that
demand for remote power feeding and meet high level requirement
for power. In addition, the SP6005P4 is equipped with DIP switch
for per-port PoE enabled/disabled. It effectively helps allocate
power for connected devices and enhances network management.
Key Features
Compliant with IEEE 802.3af and pre-802.3at standards
Supports Power over Ethernet on 4 RJ-45 ports of 10/100M
Provides 61.6W (max) feeding power to 4 PDs: 15.4W for each
Able to delivers high power to 1/2/3 PDs: 48/30/20W for each
Supports power protection as OVP (Over Voltage Protection),
OCP (Over Current Protection), OTP (Over Temperature
Protection), and SCP (Short Circuit Protection)
Supports robust surge protection
Equipped with DIP switch for per-port PoE enabled/disabled
LED indicators for PoE activity
Package Contents
Before you start installing SP6005P4, please verify the following
package contents:
SP6005P4 10/100M PoE Switch
Quick Installation Guide
AC/DC Power Adaptor
Power Cord
LED Indicator
For definitions of LED indicators, please refer to the following table
LED
STATUS
OPERATION
POWER
On/Green
Power is on
Off
Power is off
LINK
On/Green
The Ethernet port is connectingwith the device.
Blink/Green
Receiving or transmitting data.
Off
No device attached.
PoE
On/Green
PoE port is active.
Off
PoE port is not active
.Hardware Installation
The setup of the switch can be performed using the following steps:
Step 1: Connect the AC Power Adaptor to SP6005P4 and then
to a power outlet.
Step 2: Enable PoE port manually with dip switch 'On'.
Step 3: Connect a RJ-45 Ethernet cable from IEEE802.3afcompliant
devices (PD) to an available PoE port of SP6005P4.
Note:
1. Ports 1 to 4 are used for connecting to PD or PoE splitter for
end devices.
2. For high power applications, the PD or PoE splitter has to be
ompliant with pre-802.3at standard.
3. Port 5 is the RJ-45 uplink port that connects with non-PoE
Device.
1.For cable selection, refer to the following table:
Network speed
Cabletype
Max.Length
10M
Cat. 5,5e UTP/STP
100 meters
100M
Cat. 3,4,5,5e UTP/STP
100 meters
Max. Length
Note:
To prevent costly equipment damage and downtime, please
consider installing a surge suppression device or a UPS (Uninterrupted
Power Supply).
Specifications
Module
SP6005P4
Standards
IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX
IEEE 802.3af / pre-802.3at Power over Ethernet
Hardware
1 x RJ-45 ports of 10/100M (#5)
4 x RJ-45 PoE ports of 10/100M (#1 - #4)
MAC address: 2K
Buffer memory: 512KB
Features
Auto negotiation for 10/100M ports
Auto MDI/MDI-X for 10/100M ports
Max. 61.6W system feeding power
Deliver high power 48/30/20W for 1/2/3 PDs
OVP (Over Voltage Protection)
OCP (Over Current Protection)
OTP (Over Temperature Protection)
SCP (Short Circuit Protection)
Surge protection
LED indicators for PoE activity
Power supply
DC 48V, 1.25A
Environment
Operating Temperature: 0 55 degree C
Storage Temperature: -20 90 degree C
Relative Humidity: 10 to 90%
Dimension
120 x 90 x 28 (mm
Emission
CE